Toyota Tacoma manuals

Toyota Tacoma 2015-2018 Service Manual: Adjustment

ADJUSTMENT

CAUTION / NOTICE / HINT

HINT:

  • Use the same procedures for both the LH and RH sides.
  • The procedure described below is for the LH side.
  • Centering bolts are used to mount the door hinge to the vehicle body and door. The door cannot be adjusted with the centering bolts on. Substitute the centering bolts for standard bolts when making adjustments.
  • A bolt without a torque specification is shown in the standard bolt chart (See page ).

PROCEDURE

1. INSPECT FRONT DOOR PANEL SUB-ASSEMBLY (for Double Cab)

(a) Check that the clearance measurements of areas "A" through "J" are within each standard range.

Standard:

Area

Measurement

Area

Measurement

A

3.2 to 6.2 mm (0.126 to 0.244 in.)

B

3.4 to 6.4 mm (0.134 to 0.252 in.)

C

1.1 to 4.1 mm (0.043 to 0.161 in.)

D

3.3 to 6.3 mm (0.130 to 0.248 in.)

E

1.1 to 4.1 mm (0.043 to 0.161 in.)

F

3.3 to 6.3 mm (0.130 to 0.248 in.)

G

0.7 to 3.7 mm (0.028 to 0.146 in.)

H

3.5 to 6.5 mm (0.138 to 0.256 in.)

I

3.5 to 6.5 mm (0.138 to 0.256 in.)

J

0.5 to 3.5 mm (0.020 to 0.138 in.)

2. INSPECT FRONT DOOR PANEL SUB-ASSEMBLY (for Access Cab)

(a) Check that the clearance measurements of areas "A" through "J" are within each standard range.

Standard:

Area

Measurement

Area

Measurement

A

3.2 to 6.2 mm (0.126 to 0.244 in.)

B

3.4 to 6.4 mm (0.134 to 0.252 in.)

C

1.1 to 4.1 mm (0.043 to 0.161 in.)

D

3.3 to 6.3 mm (0.130 to 0.248 in.)

E

1.1 to 4.1 mm (0.043 to 0.161 in.)

F

3.3 to 6.3 mm (0.130 to 0.248 in.)

G

0.7 to 3.7 mm (0.028 to 0.146 in.)

H

4.5 to 7.5 mm (0.177 to 0.295 in.)

I

3.5 to 6.5 mm (0.138 to 0.256 in.)

J

0.5 to 3.5 mm (0.020 to 0.138 in.)

3. ADJUST FRONT DOOR PANEL SUB-ASSEMBLY

(a) Apply strips of protective tape to the door panel and fender panel, as shown in the illustration.

Text in Illustration

Protective Tape

(b) Open the door, and then disengage the 3 clips.

HINT:

If any clips are damaged, replace them with new ones.

(c) Remove the front fender side panel protector LH from the gap between the fender and door.

(d) Using SST, adjust the door horizontally and vertically by loosening the body side hinge bolts.

SST: 09812-00010

(e) Tighten the body side hinge bolts after the adjustment.

Torque:

26 NВ·m {265 kgfВ·cm, 19 ftВ·lbf}

(f) Horizontally and vertically adjust the door by loosening the door side hinge bolts.

(g) Tighten the door side hinge bolts after the adjustment.

Torque:

26 NВ·m {265 kgfВ·cm, 19 ftВ·lbf}

(h) Adjust the striker position by slightly loosening the striker mounting screws with a T40 "TORX" socket wrench and hitting the striker with a plastic hammer.

(i) Using a T40 "TORX" socket wrench, tighten the striker mounting screws after the adjustment.

Torque:

23 NВ·m {235 kgfВ·cm, 17 ftВ·lbf}

(j) Install the front fender side panel protector LH with the 3 clips.

Front Door
...

Components
COMPONENTS ILLUSTRATION *1 FRONT ARMREST BASE UPPER PANEL SUB-ASSEMBLY *2 FRONT DOOR GLASS INNER WEATHERSTRIP *3 FRONT DOOR ...

Other materials:

Installation
INSTALLATION PROCEDURE 1. INSTALL TRANSFER ASSEMBLY Click here 2. INSTALL WIRING HARNESS CLAMP BRACKET (a) Install the 4 wiring harness clamp brackets with the 4 bolts. Torque: 8.0 NВ·m {82 kgfВ·cm, 71 inВ·lbf} 3. INSTALL TRANSMISSION BREATHER SUB-ASSEMBLY (a) Install the 2 brackets to t ...

System Description
SYSTEM DESCRIPTION 1. CRUISE CONTROL SYSTEM The cruise control system makes it possible to drive at a desired speed without using the accelerator pedal. ECM controls the throttle opening angle based on signals from switches and sensors. The microcomputer which controls the cruise control syst ...

Installation
INSTALLATION PROCEDURE 1. INSTALL REAR NO. 2 POWER WINDOW REGULATOR SWITCH ASSEMBLY (a) Engage the 2 claws to install the rear No. 2 power window regulator switch assembly. 2. INSTALL INSTRUMENT PANEL LOWER CENTER FINISH PANEL Click here 3. INSTALL NO. 2 INSTRUMENT PANEL GARNISH SUB-ASSEMB ...

2015-2021 © Copyright www.luting.site