Toyota Tacoma manuals

Toyota Tacoma 2015-2018 Service Manual: Engine Switch Illumination Circuit

Toyota Tacoma 2015-2018 Service Manual / Lighting / Lighting System / Engine Switch Illumination Circuit

DESCRIPTION

The illuminated entry system controls the engine switch illumination.

WIRING DIAGRAM

PROCEDURE

PROCEDURE

1.

READ VALUE USING TECHSTREAM (POWER/ENGINE SW LIGHT)

(a) Connect the Techstream to the DLC3.

(b) Turn the engine switch to ON.

(c) Turn the Techstream on.

(d) Enter the following menus: Body Electrical / Smart Key / Active Test.

(e) Perform the Active Test according to the display on the Techstream.

Smart Key

Tester Display

Test Part

Control Range

Diagnostic Note

Power/Engine SW Light

Engine switch illumination

OFF/ON

When performing this Active Test, make sure the following condition is met:

The engine switch illumination is off (15 seconds or more have elapsed since it turned from on to off) and the engine switch is on (ACC) or on (IG), or the engine is running.

OK:

Engine switch illumination comes on.

OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.

INSPECT ENGINE SWITCH

(a) Remove the engine switch.

  • for 2TR-FE (See page for 2GR-FKS (See page  ) )
  • for 2GR-FKS (See page )

(b) Inspect the engine switch.

  • for 2TR-FE (See page for 2GR-FKS (See page  ) )
  • for 2GR-FKS (See page )

OK:

Engine switch illumination is normal.

Result

Result

Proceed to

OK

A

NG (for 2TR-FE)

B

NG (for 2GR-FKS)

C

B

REPLACE ENGINE SWITCH

C

REPLACE ENGINE SWITCH

A

3.

CHECK HARNESS AND CONNECTOR (ENGINE SWITCH - CERTIFICATION ECU (SMART KEY ECU ASSEMBLY))

(a) Disconnect the C29 certification ECU (smart key ECU assembly) connector.

(b) Disconnect the E28 engine switch connector.

(c) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

E28-9 (SWIL) - C29-17 (SWIL)

Always

Below 1 О©

E28-6 (AGND) - C29-12 (AGND)

Always

Below 1 О©

E28-9 (SWIL) - Body ground

Always

10 kО© or higher

E28-6 (AGND) - Body ground

Always

10 kО© or higher

OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

Interior Light Circuit
DESCRIPTION The illuminated entry system controls the interior lights. WIRING DIAGRAM CAUTION / NOTICE / HINT NOTICE: Inspect the fuses for circuits related to this system before perfor ...

Taillight Relay Circuit
DESCRIPTION The main body ECU (multiplex network body ECU) controls the operation of the TAIL relay. WIRING DIAGRAM CAUTION / NOTICE / HINT NOTICE: Inspect the fuses for circuits rela ...

Other materials:

Terminals Of Ecu
TERMINALS OF ECU 1. ECM Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition E14-20 (TC) - E11-1 (E1) G - W-B DTC output signal Ignition switch ON ...

Terminals Of Ecu
TERMINALS OF ECU 1. CHECK TIRE PRESSURE WARNING ECU AND RECEIVER (a) Disconnect the T14 tire pressure warning ECU and receiver connector and measure the voltage and resistance on the wire harness side. Text in Illustration *A w/o Wireless Door Lock System ...

Tire Pressure Monitor ECU Communication Stop (C2179/79)
DESCRIPTION The main body ECU (multiplex network body ECU) sends signals to the tire pressure warning ECU and receiver via a direct line. DTC No. Detection Item DTC Detection Condition Trouble Area Note C2179/79 T ...

2015-2021 © Copyright www.luting.site