Toyota Tacoma manuals

Toyota Tacoma 2015-2018 Service Manual: Open in ABS Solenoid Relay Circuit (C146E,C146F)

DESCRIPTION

The ABS solenoid relay is built into the master cylinder solenoid.

This relay supplies power to each ABS solenoid. After the ignition switch is turned ON, if the initial check is OK, the relay turns on.

DTC No.

DTC Detecting Conditions

Trouble Areas

C146E

When either of following condition detected:

  1. Both of following conditions continue for at least 0.2 seconds.
    1. IG voltage between 9.5 V and 17 V.
    2. Relay contact open when relay ON
  2. Both of the following conditions continue for at least 0.2 seconds.
    1. IG voltage 9.5 V or less when relay ON.
    2. Relay contact remains open.
  • ABS NO. 2 fuse
  • ABS solenoid relay
  • ABS solenoid relay circuit
  • Master cylinder solenoid

C146F

The following condition continues for at least 0.2 seconds.

  • Relay contact closed immediately after turning IG switch to the ON position when the relay OFF.
  • ABS NO. 2 fuse
  • ABS solenoid relay
  • ABS solenoid relay circuit
  • Master cylinder solenoid

WIRING DIAGRAM

CAUTION / NOTICE / HINT

CAUTION / NOTICE / HINT

NOTICE:

  • When replacing the skid control ECU (master cylinder solenoid), perform zero point calibration (See page ). Inspect the fuses for circuits related to this system before performing ).
  • Inspect the fuses for circuits related to this system before performing the following inspection procedure.

PROCEDURE

1.

INSPECT SKID CONTROL ECU CONNECTOR (+BS TERMINAL VOLTAGE)

(a) Disconnect the skid control ECU connector.

(b) Measure the voltage.

Standard Voltage:

Tester Connection

Specified Condition

S1-31 (+BS) - Body ground

10 to 14 V

(c) Reconnect the skid control ECU connector.

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

OK

2.

CHECK HARNESS OR CONNECTOR (GND - BODY GROUND)

(a) Disconnect the skid control ECU connectors.

(b) Measure the resistance.

Standard Resistance:

Tester Connection

Specified Condition

S1-1, 32 (GND1, GND2) - Body ground

Below 1 О©

S2-4 (GND3) - Body ground

Below 1 О©

(c) Reconnect the skid control ECU connectors.

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (GND CIRCUIT)

OK

3.

RECONFIRM DTC

(a) Clear the DTCs (See page ). (b) Check if the same DTCs are recorded. ).

(b) Check if the same DTCs are recorded.

Result

Proceed to

DTC output

A

DTC not output

B

A

REPLACE MASTER CYLINDER SOLENOID

B

END

Abnormal Change in Output Signal of Rear Speed Sensor RH (Test Mode DTC) (C1277,...,C1416)
DESCRIPTION Refer to DTCs C1401 and C1402 (See page ). DTC Code DTC Detection Condition Trouble Area C1277 C1278 Stored only during t ...

ECM Communication Circuit Malfunction (C1203)
DESCRIPTION The circuit sends TRAC, A-TRAC and VSC control information from the skid control ECU (master cylinder solenoid) to the ECM, and engine control information from the ECM to the skid con ...

Other materials:

Compass (vehicles with auto anti-glare inside rear view mirror)
The compass on the inside rear view mirror indicates the direction in which the vehicle is heading. ■ Operation Type A To turn the compass on or off, press the button. Type B ■ Displays and directions Calibrating the compass The direction display deviates from the true ...

Disposal
DISPOSAL CAUTION / NOTICE / HINT CAUTION: Before performing pre-disposal deployment of any SRS part, review and closely follow all applicable environmental and hazardous material regulations. Pre-disposal deployment may be considered hazardous material treatment. PROCEDURE 1. PRECAUTION ...

Disassembly
DISASSEMBLY PROCEDURE 1. REMOVE STEERING GEAR OUTLET RETURN TUBE (a) Using a union nut wrench, remove the steering gear outlet return tube. 2. REMOVE STEERING TURN PRESSURE TUBE (a) Using a union nut wrench, remove the 2 pressure tubes. (b) Remove the 4 O-rings from the pressure tubes. 3. ...

2015-2021 © Copyright www.luting.site