Toyota Tacoma manuals

Toyota Tacoma 2015-2018 Service Manual: Reassembly

REASSEMBLY

CAUTION / NOTICE / HINT

NOTICE:

  • When installing the hood bulge protector, heat the hood bulge surface using the infrared light.
  • Do not heat the hood bulge excessively.

    Item

    Temperature

    Hood Bulge

    20 to 30В°C (68 to 86В°F)

PROCEDURE

1. INSTALL HOOD LOCK CONTROL CABLE ASSEMBLY

(a) Tie the string that was passed thorough the engine compartment room to the end of the hood lock control cable assembly as shown in the illustration.

(b) Pass the hood lock control cable assembly into the engine compartment.

(c) Engage the 5 clamps and hood cable grommet as shown in the illustration.

(d) Remove the string from the hood lock control cable assembly.

(d) Remove the string from the hood lock control cable assembly.

2. INSTALL HOOD LOCK CONTROL LEVER SUB-ASSEMBLY

(a) Connect the hood lock control cable assembly to install the hood lock control lever sub-assembly.

(b) Engage the claw and 3 guides to install the hood lock control lever sub-assembly.

3. INSTALL HOOD STAY HOLDER

(a) Engage the 2 claws to install the hood stay holder.

4. INSTALL HOOD SUPPORT

(a) Install the grommet.

(b) Install the hood support.

5. INSTALL HOOD LOCK ASSEMBLY

6. INSTALL RADIATOR GRILLE

6. INSTALL RADIATOR GRILLE

7. CONNECT WASHER HOSE ASSEMBLY 7. CONNECT WASHER HOSE ASSEMBLY

7. CONNECT WASHER HOSE ASSEMBLY

(a) Engage the 4 claws to install the 4 clamps.

(b) Engage the 4 clamps to connect the washer hose assembly.

8. INSTALL WASHER NOZZLE SUB-ASSEMBLY

9. INSTALL HOOD TO RADIATOR SUPPORT SEAL

9. INSTALL HOOD TO RADIATOR SUPPORT SEAL

(a) Install the 7 clips and hood to radiator support seal.

10. INSTALL NO. 1 HOOD BULGE PROTECTOR (w/ Hood Bulge)

(a) Install the No. 1 hood bulge protector.

11. INSTALL HOOD AIR INTAKE GUIDE (w/ Hood Bulge)

(a) Engage the 5 guides to install the hood air intake guide.

(b) Install the 4 screws.

12. INSTALL NO. 2 HOOD BULGE PROTECTOR (w/ Hood Bulge)

(a) Install the No. 2 hood bulge protector.

13. INSTALL HOOD BULGE ASSEMBLY (w/ Hood Bulge)

(a) Engage the clip from the back side of the hood panel to install the hood bulge assembly together with the air intake guide.

(b) Install the 4 nuts.

Disassembly
DISASSEMBLY PROCEDURE 1. REMOVE HOOD BULGE ASSEMBLY (w/ Hood Bulge) (a) Remove the 4 nuts. (b) Disengage the clip from back side of the hood pa ...

Rear Door(for Access Cab)
Adjustment ADJUSTMENT CAUTION / NOTICE / HINT HINT: Use the same procedures for both the LH and RH sides. The procedure described below is for the LH side. Centering bolts are us ...

Other materials:

Theft Deterrent System Communication Line High Fixation (B279A,B279A12)
DESCRIPTION If the communication line (EFIO-IMI) to the transponder key ECU assembly is stuck high (e.g. shorted to +B), the ECM stores this DTC. DTC No. DTC Detection Condition Trouble Area DTC Output Confirmation Operation B279A*1 ...

On-vehicle Inspection
ON-VEHICLE INSPECTION PROCEDURE 1. INSPECT FLUID LEVEL IN RESERVOIR (a) Check the fluid level. If the brake fluid level is lower than the MIN line, check for leaks and inspect the disc brake pads. If necessary, refill the reservoir with brake fluid to the MAX line after repair or replaceme ...

Front Wiper Rubber
Components COMPONENTS ILLUSTRATION Installation INSTALLATION PROCEDURE 1. INSTALL FRONT WIPER RUBBER (a) Install the 2 wiper rubber backing plates to the front wiper rubber. NOTICE: Align the groove of the front wiper rubber backing plate with the edg ...

2015-2021 © Copyright www.luting.site