Toyota Tacoma manuals

Toyota Tacoma 2015-2018 Service Manual: Remote Control System does not Operate

Toyota Tacoma 2015-2018 Service Manual / Sliding Roof / Sliding Roof System / Remote Control System does not Operate

DESCRIPTION

The main body ECU (multiplex network body ECU) receives remote control signals from the driver door key cylinder or wireless transmitter. Then, the main body ECU (multiplex network body ECU) sends the remote control signals to the sliding roof ECU (sliding roof drive gear sub-assembly) via LIN communication. The sliding roof ECU (sliding roof drive gear sub-assembly) receives those signals and activates the sliding roof motor.

CAUTION / NOTICE / HINT

NOTICE:

  • The sliding roof key-linked function and sliding roof wireless transmitter-linked function can be customized. Make sure that both functions are ON (See page When the sliding roof ECU (sliding roof drive gear sub-assembly) is ).
  • When the sliding roof ECU (sliding roof drive gear sub-assembly) is removed and reinstalled or replaced, the sliding roof ECU (sliding roof drive gear sub-assembly) must be initialized (See page Since the sliding roof system has functions that use LIN communication, ).
  • Since the sliding roof system has functions that use LIN communication, first confirm that there is no malfunction in the LIN communication system with the How to Proceed with Troubleshooting procedure (See page When sliding roof ECU (sliding roof drive gear sub-assembly) DTC is ).
  • When sliding roof ECU (sliding roof drive gear sub-assembly) DTC is output, first perform troubleshooting for the sliding roof ECU (sliding roof drive gear sub-assembly) DTC.

PROCEDURE

1.

CHECK REMOTE CONTROL FUNCTION

(a) Check the key-linked and wireless transmitter-linked function (See page ).

Result

Proceed to

The roof glass does not operate by the key-linked or wireless transmitter-linked function,

A

The roof glass operates by both the key-linked and wireless transmitter-linked function.

B

B

USE SIMULATION METHOD TO CHECK

A

2.

CHECK SLIDING ROOF OPERATION

(a) Check the sliding roof operation (See page OK: ).

OK:

Sliding roof operation operates normally.

NG

GO TO OTHER PROBLEM (Sliding Roof does not Move by Operating Sliding Roof Control)

OK

3.

REPLACE SLIDING ROOF ECU (SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY)

(a) Replace the sliding roof ECU (sliding roof drive gear sub-assembly) (See page ).

NEXT

4.

INITIALIZE SLIDING ROOF ECU (SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY)

(a) Initialize the sliding roof ECU (sliding roof drive gear sub-assembly) (See page ).

NEXT

5.

CHECK REMOTE CONTROL FUNCTION

(a) Check the key-linked and wireless transmitter-linked function (See page OK: ).

OK:

The key-linked and wireless transmitter-linked function operates normally.

OK

END (SLIDING ROOF ECU WAS DEFECTIVE)

NG

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

Sensor (Motor) Failure (B2341,B2344)
DESCRIPTION When the sliding roof ECU (sliding roof drive gear sub-assembly) detects a motor malfunction and the sliding roof operation is stopped, DTC B2341 is stored. When the sliding roof ECU ( ...

Sliding Roof does not Move by Operating Sliding Roof Control Switch
DESCRIPTION The sliding roof ECU (sliding roof drive gear sub-assembly) receives slide and tilt signals when the sliding roof switch is operated and drives its built-in motor. WIRING DIAGRAM CA ...

Other materials:

Disassembly
DISASSEMBLY PROCEDURE 1. REMOVE PRESSURE RELIEF VALVE (a) Remove the pressure relief valve and O-ring. 2. REMOVE MAGNET CLUTCH ASSEMBLY (a) Secure the cooler compressor assembly in a vise between aluminum plates. (b) Using SST, hold the magnet clutch hub. SST: 09985-00260 (c) Remove the ...

Problem Symptoms Table
PROBLEM SYMPTOMS TABLE HINT: Use the table below to help determine the cause of problem symptoms. If multiple suspected areas are listed, the potential causes of the symptoms are listed in order of probability in the "Suspected Area" column of the table. Check each symptom by check ...

Removal
REMOVAL PROCEDURE 1. PRECAUTION NOTICE: After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before pr ...

2015-2021 © Copyright www.luting.site